E-max瓷块厚度及颜色对光固化树脂固化率的影响

›› 2018, Vol. 38 ›› Issue (2): 135-137.

E-max瓷块厚度及颜色对光固化树脂固化率的影响

朱明月¹,魏宁²,石旭旭³,朴国宾⁴,赵跃峰⁵,陈群芬⁵

1. 佳木斯大学
2. 大庆市人民医院
3. 大庆油田总医院
4. 大庆市油田总医院
5. 大庆油田总医院门诊部口腔修复科

收稿日期:2016-11-28 修回日期:2017-02-17 出版日期:2018-02-28 发布日期:2018-02-07
通讯作者: 石旭旭 E-mail:Shixuxu@tom.com

Effect of thickness and color of E-max ceramic on curing rate of light cured resin

Received:2016-11-28 Revised:2017-02-17 Online:2018-02-28 Published:2018-02-07

摘要/Abstract

摘要： 目的测定不同颜色不同厚度的Emax瓷块下光固化树脂能否充分固化，以利于指导临床Emax瓷贴面美学修复过小牙、扭转牙时，贴面最大厚度的设定。方法采用傅立叶变换红外光谱技术测量不同颜色（A1、B1、C1、A4、B4、C4）和不同厚度（2.0 mm、2.2 mm、2.4 mm、2.6 mm、2.8 mm、3.0 mm）CEREC制作Emax瓷片下光固化复合树脂的相对固化率。结果当光照时间为120 s时，A1、B1、C1色陶瓷厚度≤2.6 mm时可使树脂充分固化，A4、B4、C4色陶瓷厚度≤2.2 mm时可使树脂充分固化。浅色陶瓷间的固化率无统计学差异（P＞0.05），同一厚度下浅色陶瓷与深色陶瓷间的固化率有统计学差异（P＜0.01），深色陶瓷下树脂的固化率明显低于浅色陶瓷。结论随着颜色的加深和厚度的增加树脂的固化率明显下降，说明Emax瓷片的厚度和颜色对光固化树脂的固化率有明显影响。

关键词: E-max瓷块, 光固化树脂, 固化率, 红外光谱

Abstract: Objective To determine whether under the Emax ceramic block with different thicknesses and different colors the light cured resin can be fully cured, to facilitate clinical Emax ceramic veneer aesthetic restoration of microdontia, teeth when reversed, and to set the maximum thickness of the stick side. Methods By using Fourier transform infrared spectroscopy,the curing rate of light composite resin of EMAX porcelain block was measured by CEREC chip with different colors (A1, A4, B1, B4, C1, C4) and different thicknesses (2.0 mm, 2.2 mm, 2.4 mm, 2.6 mm, 2.8 mm, 3.0 mm) . Results When the illumination time was 120 s, and A1, B1, C1 color ceramic thickness was less than or equal to 2.6mm, the resin was fully cured. When A4, B4, C4 color ceramic thickness was less than or equal to 2.2 mm, the resin was fully cured. Curing rate was not statistically different between the light colored ceramics（P＞0.05）. There was a statistical difference in the cure rate between the light colored ceramic and the dark ceramic（P＜0.01）. The cure rate of the resin of dark ceramic was obviously lower than that of the light colored ceramic. Conclusion The curing rate of the resin obviously decreases with the increase of the ceramic color and the thickness, the thickness and color of Emax ceramic have obvious influence on the cure rate of light cured resin.

Key words: E-max ceramic block, light cured resin, cure rate, infrared spectroscopy

中图分类号:

R783.1

朱明月魏宁石旭旭朴国宾赵跃峰陈群芬. E-max瓷块厚度及颜色对光固化树脂固化率的影响[J]. , 2018, 38(2): 135-137.

参考文献

[1]Mitsuo N, Hideo M.The 24year clinical performance of porcelain laminate veneer restorations bonded with a twoliquid silane primer and a trinbutylboraneinitiated adhesive resin[J][J].Oral Science, 2014, 56(3):227-230
[2]Peumans M, De Munck J, Fieuws S, et al.A prospective tenyear clinical trial of porcelain veneers[J].Adhes Dent, 2004, 6(1):65-76
[3]Vinod KG, Soorya PT, Bipin R, et al.A study on provisional cements,cementation techniques,and their effects on bonding of porcelain laminate veneers[J][J].Indian Prosthodont Soc, 2014, 14(1):42-49
[4]王桂清, 刘敏娜.红外光谱技术的近代进展及其应用[J].现代仪器, 2001, 7(6):9-12
[5]Rueggeberg FA, Hashinger DT, Fairhurst CW.Calibration of FTIR conversion analysis of contemporary dental resin composites[J].Dent Mater, 1990, 6(4):241-249
[6] 〖ＺＫ（#〗王军.牙用复合树脂聚合的傅立叶变换红外光谱研究［D］. 西安:第四军医大学，1995.
[7]Beier US, Kapferer I, Burtscher D, et al.Clinical performance of porcelain laminate veneers for up to 20 years[J].Prosthodont, 2012, 25(1):79-85
[8]Fradeani M, Redemagni M, Corrado M.Porcelain laminate veneers: 6to12year clinical evaluation– a retrospective study[J].Periodontics Restorative Dent, 2005, 25(6):9-17
[9]Peumans M, De Munck J, Fieuws S, et al.A prospective tenyear clinical trial of porcelainveneers[J].Adhes Dent, 2004, 6(1):65-76
[10]Arcangelo C, De Angelis F, Vadini M, et al.Clinical evaluation on porcelain laminate veneers bonded with lightcured composite: results up to 7 years[J].Clin Oral Investig, 2012, 16(4):1071-1079
[11]Strassler HE, Nathanson D.Clinical evaluation of etched porcelain veneers over a period of 18～42 mouths［J］. Esthet Dent, 1989, 1:21-28.
[12]Breschi L, Mazzoni A, Ruggeri A, et al.Dental adhesionreview:aging and stability of the bonded interface[J].Dent Mater, 2008, 24(1):90-101
[13]da Silva EM, Poskus LT, Guimares JG, et al.Influence of light polymerization modes on degree of conversion and crosslink density of dental composites[J].J Mater Sci Med, 2008, 19(3):1027-1032
[14]王军, 施长溪, 陈天池, 等.陶瓷厚度和颜色对光固化复合树脂聚合程度的影响[J].实用口腔医学杂志, 1995, 11(2):107-109
[15]陈吉华，周国锋，卫张蕊, 等.瓷贴面及人牙釉质透射率的测定与比较[J].华西口腔医学杂志, 2006, 24(6):513-515
[16]Ma TT, Yi YF, Shao LQ, et al.Test of relative translucency for three veneered allceramic systems core material[J].Advanced Mater Res, 2011, 1096(177):302-305
[17]Jung H, Friedl KH, Hiller KA, et al.SchmalzCuring efficiency of different polymerization methods through ceramic restorations[J].Clin Oral Investig, 2001, 5(3):156-161